Your cart is currently empty!
Victron BlueSolar PWM-LCD&USB 48V-20A
$53.79
Features: – Liquid Crystal Display – Two 5 Volt USB outputs – Lighting control function, fully programmable – Three stage battery charging (bulk, absorption, float), fully programmable – Load output with low voltage and manual disconnect (programmable) – Load output protected against over load and short circuit – Protected against reverse polarity connection of the…
Description
A solar charger gathers energy from your solar panels, and stores it in your batteries. The PWM controller is in essence a switch that connects a solar array to a battery. The result is that the voltage of the array will be pulled down to near that of the battery. The Victron PWM charge controller is a good low cost solution for small systems only, when solar cell temperature is moderate to high (between 45°C and 75°C).
Liquid crystal display- For status monitoring and set-up
Load output- Over-discharge of the battery can be prevented by connecting all loads to the load output. The load output will disconnect the load when the battery has been discharged to a pre-set voltage. Some loads (especially inverters) can best be connected directly to the battery, and the inverter remote control connected to the load output. A special interface cable may be needed, please see the manual. The connect and disconnect voltages are adjustable.
Day/night timing of the load output- This option allows for a pre-set ON-time after dusk.
Programmable battery charge algorithm- Pre-programmed algorithms for AGM, GEL, Flooded or LiFePO4 batteries (with internal BMS only)
Two 5 Volt USB outputs- Maximum current (both outputs combined): 2A
Additional information
| Weight | 0.330000 kg |
|---|---|
| Dimensions | 11 × 19 × 5 cm |
Description
A solar charger gathers energy from your solar panels, and stores it in your batteries. The PWM controller is in essence a switch that connects a solar array to a battery. The result is that the voltage of the array will be pulled down to near that of the battery. The Victron PWM charge controller is a good low cost solution for small systems only, when solar cell temperature is moderate to high (between 45°C and 75°C).
Liquid crystal display- For status monitoring and set-up
Load output- Over-discharge of the battery can be prevented by connecting all loads to the load output. The load output will disconnect the load when the battery has been discharged to a pre-set voltage. Some loads (especially inverters) can best be connected directly to the battery, and the inverter remote control connected to the load output. A special interface cable may be needed, please see the manual. The connect and disconnect voltages are adjustable.
Day/night timing of the load output- This option allows for a pre-set ON-time after dusk.
Programmable battery charge algorithm- Pre-programmed algorithms for AGM, GEL, Flooded or LiFePO4 batteries (with internal BMS only)
Two 5 Volt USB outputs- Maximum current (both outputs combined): 2A
Additional information
| Weight | 0.330000 kg |
|---|---|
| Dimensions | 11 × 19 × 5 cm |
Reviews
There are no reviews yet.
Description
A solar charger gathers energy from your solar panels, and stores it in your batteries. The PWM controller is in essence a switch that connects a solar array to a battery. The result is that the voltage of the array will be pulled down to near that of the battery. The Victron PWM charge controller is a good low cost solution for small systems only, when solar cell temperature is moderate to high (between 45°C and 75°C).
Liquid crystal display- For status monitoring and set-up
Load output- Over-discharge of the battery can be prevented by connecting all loads to the load output. The load output will disconnect the load when the battery has been discharged to a pre-set voltage. Some loads (especially inverters) can best be connected directly to the battery, and the inverter remote control connected to the load output. A special interface cable may be needed, please see the manual. The connect and disconnect voltages are adjustable.
Day/night timing of the load output- This option allows for a pre-set ON-time after dusk.
Programmable battery charge algorithm- Pre-programmed algorithms for AGM, GEL, Flooded or LiFePO4 batteries (with internal BMS only)
Two 5 Volt USB outputs- Maximum current (both outputs combined): 2A
Additional information
| Weight | 0.330000 kg |
|---|---|
| Dimensions | 11 × 19 × 5 cm |
Reviews
There are no reviews yet.
Description
A solar charger gathers energy from your solar panels, and stores it in your batteries. The PWM controller is in essence a switch that connects a solar array to a battery. The result is that the voltage of the array will be pulled down to near that of the battery. The Victron PWM charge controller is a good low cost solution for small systems only, when solar cell temperature is moderate to high (between 45°C and 75°C).
Liquid crystal display- For status monitoring and set-up
Load output- Over-discharge of the battery can be prevented by connecting all loads to the load output. The load output will disconnect the load when the battery has been discharged to a pre-set voltage. Some loads (especially inverters) can best be connected directly to the battery, and the inverter remote control connected to the load output. A special interface cable may be needed, please see the manual. The connect and disconnect voltages are adjustable.
Day/night timing of the load output- This option allows for a pre-set ON-time after dusk.
Programmable battery charge algorithm- Pre-programmed algorithms for AGM, GEL, Flooded or LiFePO4 batteries (with internal BMS only)
Two 5 Volt USB outputs- Maximum current (both outputs combined): 2A
Additional information
| Weight | 0.330000 kg |
|---|---|
| Dimensions | 11 × 19 × 5 cm |
Reviews
There are no reviews yet.
Description
A solar charger gathers energy from your solar panels, and stores it in your batteries. The PWM controller is in essence a switch that connects a solar array to a battery. The result is that the voltage of the array will be pulled down to near that of the battery. The Victron PWM charge controller is a good low cost solution for small systems only, when solar cell temperature is moderate to high (between 45°C and 75°C).
Liquid crystal display- For status monitoring and set-up
Load output- Over-discharge of the battery can be prevented by connecting all loads to the load output. The load output will disconnect the load when the battery has been discharged to a pre-set voltage. Some loads (especially inverters) can best be connected directly to the battery, and the inverter remote control connected to the load output. A special interface cable may be needed, please see the manual. The connect and disconnect voltages are adjustable.
Day/night timing of the load output- This option allows for a pre-set ON-time after dusk.
Programmable battery charge algorithm- Pre-programmed algorithms for AGM, GEL, Flooded or LiFePO4 batteries (with internal BMS only)
Two 5 Volt USB outputs- Maximum current (both outputs combined): 2A
Additional information
| Weight | 0.330000 kg |
|---|---|
| Dimensions | 11 × 19 × 5 cm |
Reviews
There are no reviews yet.
Description
A solar charger gathers energy from your solar panels, and stores it in your batteries. The PWM controller is in essence a switch that connects a solar array to a battery. The result is that the voltage of the array will be pulled down to near that of the battery. The Victron PWM charge controller is a good low cost solution for small systems only, when solar cell temperature is moderate to high (between 45°C and 75°C).
Liquid crystal display- For status monitoring and set-up
Load output- Over-discharge of the battery can be prevented by connecting all loads to the load output. The load output will disconnect the load when the battery has been discharged to a pre-set voltage. Some loads (especially inverters) can best be connected directly to the battery, and the inverter remote control connected to the load output. A special interface cable may be needed, please see the manual. The connect and disconnect voltages are adjustable.
Day/night timing of the load output- This option allows for a pre-set ON-time after dusk.
Programmable battery charge algorithm- Pre-programmed algorithms for AGM, GEL, Flooded or LiFePO4 batteries (with internal BMS only)
Two 5 Volt USB outputs- Maximum current (both outputs combined): 2A
Additional information
| Weight | 0.330000 kg |
|---|---|
| Dimensions | 11 × 19 × 5 cm |
Reviews
There are no reviews yet.
Description
A solar charger gathers energy from your solar panels, and stores it in your batteries. The PWM controller is in essence a switch that connects a solar array to a battery. The result is that the voltage of the array will be pulled down to near that of the battery. The Victron PWM charge controller is a good low cost solution for small systems only, when solar cell temperature is moderate to high (between 45°C and 75°C).
Liquid crystal display- For status monitoring and set-up
Load output- Over-discharge of the battery can be prevented by connecting all loads to the load output. The load output will disconnect the load when the battery has been discharged to a pre-set voltage. Some loads (especially inverters) can best be connected directly to the battery, and the inverter remote control connected to the load output. A special interface cable may be needed, please see the manual. The connect and disconnect voltages are adjustable.
Day/night timing of the load output- This option allows for a pre-set ON-time after dusk.
Programmable battery charge algorithm- Pre-programmed algorithms for AGM, GEL, Flooded or LiFePO4 batteries (with internal BMS only)
Two 5 Volt USB outputs- Maximum current (both outputs combined): 2A
Additional information
| Weight | 0.330000 kg |
|---|---|
| Dimensions | 11 × 19 × 5 cm |
Reviews
There are no reviews yet.
Description
A solar charger gathers energy from your solar panels, and stores it in your batteries. The PWM controller is in essence a switch that connects a solar array to a battery. The result is that the voltage of the array will be pulled down to near that of the battery. The Victron PWM charge controller is a good low cost solution for small systems only, when solar cell temperature is moderate to high (between 45°C and 75°C).
Liquid crystal display- For status monitoring and set-up
Load output- Over-discharge of the battery can be prevented by connecting all loads to the load output. The load output will disconnect the load when the battery has been discharged to a pre-set voltage. Some loads (especially inverters) can best be connected directly to the battery, and the inverter remote control connected to the load output. A special interface cable may be needed, please see the manual. The connect and disconnect voltages are adjustable.
Day/night timing of the load output- This option allows for a pre-set ON-time after dusk.
Programmable battery charge algorithm- Pre-programmed algorithms for AGM, GEL, Flooded or LiFePO4 batteries (with internal BMS only)
Two 5 Volt USB outputs- Maximum current (both outputs combined): 2A
Additional information
| Weight | 0.330000 kg |
|---|---|
| Dimensions | 11 × 19 × 5 cm |
Reviews
There are no reviews yet.
Description
A solar charger gathers energy from your solar panels, and stores it in your batteries. The PWM controller is in essence a switch that connects a solar array to a battery. The result is that the voltage of the array will be pulled down to near that of the battery. The Victron PWM charge controller is a good low cost solution for small systems only, when solar cell temperature is moderate to high (between 45°C and 75°C).
Liquid crystal display- For status monitoring and set-up
Load output- Over-discharge of the battery can be prevented by connecting all loads to the load output. The load output will disconnect the load when the battery has been discharged to a pre-set voltage. Some loads (especially inverters) can best be connected directly to the battery, and the inverter remote control connected to the load output. A special interface cable may be needed, please see the manual. The connect and disconnect voltages are adjustable.
Day/night timing of the load output- This option allows for a pre-set ON-time after dusk.
Programmable battery charge algorithm- Pre-programmed algorithms for AGM, GEL, Flooded or LiFePO4 batteries (with internal BMS only)
Two 5 Volt USB outputs- Maximum current (both outputs combined): 2A
Additional information
| Weight | 0.330000 kg |
|---|---|
| Dimensions | 11 × 19 × 5 cm |
Reviews
There are no reviews yet.
Description
A solar charger gathers energy from your solar panels, and stores it in your batteries. The PWM controller is in essence a switch that connects a solar array to a battery. The result is that the voltage of the array will be pulled down to near that of the battery. The Victron PWM charge controller is a good low cost solution for small systems only, when solar cell temperature is moderate to high (between 45°C and 75°C).
Liquid crystal display- For status monitoring and set-up
Load output- Over-discharge of the battery can be prevented by connecting all loads to the load output. The load output will disconnect the load when the battery has been discharged to a pre-set voltage. Some loads (especially inverters) can best be connected directly to the battery, and the inverter remote control connected to the load output. A special interface cable may be needed, please see the manual. The connect and disconnect voltages are adjustable.
Day/night timing of the load output- This option allows for a pre-set ON-time after dusk.
Programmable battery charge algorithm- Pre-programmed algorithms for AGM, GEL, Flooded or LiFePO4 batteries (with internal BMS only)
Two 5 Volt USB outputs- Maximum current (both outputs combined): 2A
Additional information
| Weight | 0.330000 kg |
|---|---|
| Dimensions | 11 × 19 × 5 cm |
Reviews
There are no reviews yet.
Description
A solar charger gathers energy from your solar panels, and stores it in your batteries. The PWM controller is in essence a switch that connects a solar array to a battery. The result is that the voltage of the array will be pulled down to near that of the battery. The Victron PWM charge controller is a good low cost solution for small systems only, when solar cell temperature is moderate to high (between 45°C and 75°C).
Liquid crystal display- For status monitoring and set-up
Load output- Over-discharge of the battery can be prevented by connecting all loads to the load output. The load output will disconnect the load when the battery has been discharged to a pre-set voltage. Some loads (especially inverters) can best be connected directly to the battery, and the inverter remote control connected to the load output. A special interface cable may be needed, please see the manual. The connect and disconnect voltages are adjustable.
Day/night timing of the load output- This option allows for a pre-set ON-time after dusk.
Programmable battery charge algorithm- Pre-programmed algorithms for AGM, GEL, Flooded or LiFePO4 batteries (with internal BMS only)
Two 5 Volt USB outputs- Maximum current (both outputs combined): 2A
Additional information
| Weight | 0.330000 kg |
|---|---|
| Dimensions | 11 × 19 × 5 cm |
Reviews
There are no reviews yet.
Description
A solar charger gathers energy from your solar panels, and stores it in your batteries. The PWM controller is in essence a switch that connects a solar array to a battery. The result is that the voltage of the array will be pulled down to near that of the battery. The Victron PWM charge controller is a good low cost solution for small systems only, when solar cell temperature is moderate to high (between 45°C and 75°C).
Liquid crystal display- For status monitoring and set-up
Load output- Over-discharge of the battery can be prevented by connecting all loads to the load output. The load output will disconnect the load when the battery has been discharged to a pre-set voltage. Some loads (especially inverters) can best be connected directly to the battery, and the inverter remote control connected to the load output. A special interface cable may be needed, please see the manual. The connect and disconnect voltages are adjustable.
Day/night timing of the load output- This option allows for a pre-set ON-time after dusk.
Programmable battery charge algorithm- Pre-programmed algorithms for AGM, GEL, Flooded or LiFePO4 batteries (with internal BMS only)
Two 5 Volt USB outputs- Maximum current (both outputs combined): 2A
Additional information
| Weight | 0.330000 kg |
|---|---|
| Dimensions | 11 × 19 × 5 cm |
Reviews
There are no reviews yet.
Description
A solar charger gathers energy from your solar panels, and stores it in your batteries. The PWM controller is in essence a switch that connects a solar array to a battery. The result is that the voltage of the array will be pulled down to near that of the battery. The Victron PWM charge controller is a good low cost solution for small systems only, when solar cell temperature is moderate to high (between 45°C and 75°C).
Liquid crystal display- For status monitoring and set-up
Load output- Over-discharge of the battery can be prevented by connecting all loads to the load output. The load output will disconnect the load when the battery has been discharged to a pre-set voltage. Some loads (especially inverters) can best be connected directly to the battery, and the inverter remote control connected to the load output. A special interface cable may be needed, please see the manual. The connect and disconnect voltages are adjustable.
Day/night timing of the load output- This option allows for a pre-set ON-time after dusk.
Programmable battery charge algorithm- Pre-programmed algorithms for AGM, GEL, Flooded or LiFePO4 batteries (with internal BMS only)
Two 5 Volt USB outputs- Maximum current (both outputs combined): 2A
Additional information
| Weight | 0.330000 kg |
|---|---|
| Dimensions | 11 × 19 × 5 cm |
Reviews
There are no reviews yet.
Description
A solar charger gathers energy from your solar panels, and stores it in your batteries. The PWM controller is in essence a switch that connects a solar array to a battery. The result is that the voltage of the array will be pulled down to near that of the battery. The Victron PWM charge controller is a good low cost solution for small systems only, when solar cell temperature is moderate to high (between 45°C and 75°C).
Liquid crystal display- For status monitoring and set-up
Load output- Over-discharge of the battery can be prevented by connecting all loads to the load output. The load output will disconnect the load when the battery has been discharged to a pre-set voltage. Some loads (especially inverters) can best be connected directly to the battery, and the inverter remote control connected to the load output. A special interface cable may be needed, please see the manual. The connect and disconnect voltages are adjustable.
Day/night timing of the load output- This option allows for a pre-set ON-time after dusk.
Programmable battery charge algorithm- Pre-programmed algorithms for AGM, GEL, Flooded or LiFePO4 batteries (with internal BMS only)
Two 5 Volt USB outputs- Maximum current (both outputs combined): 2A
Additional information
| Weight | 0.330000 kg |
|---|---|
| Dimensions | 11 × 19 × 5 cm |
Reviews
There are no reviews yet.
Description
A solar charger gathers energy from your solar panels, and stores it in your batteries. The PWM controller is in essence a switch that connects a solar array to a battery. The result is that the voltage of the array will be pulled down to near that of the battery. The Victron PWM charge controller is a good low cost solution for small systems only, when solar cell temperature is moderate to high (between 45°C and 75°C).
Liquid crystal display- For status monitoring and set-up
Load output- Over-discharge of the battery can be prevented by connecting all loads to the load output. The load output will disconnect the load when the battery has been discharged to a pre-set voltage. Some loads (especially inverters) can best be connected directly to the battery, and the inverter remote control connected to the load output. A special interface cable may be needed, please see the manual. The connect and disconnect voltages are adjustable.
Day/night timing of the load output- This option allows for a pre-set ON-time after dusk.
Programmable battery charge algorithm- Pre-programmed algorithms for AGM, GEL, Flooded or LiFePO4 batteries (with internal BMS only)
Two 5 Volt USB outputs- Maximum current (both outputs combined): 2A
Additional information
| Weight | 0.330000 kg |
|---|---|
| Dimensions | 11 × 19 × 5 cm |
Reviews
There are no reviews yet.
Description
A solar charger gathers energy from your solar panels, and stores it in your batteries. The PWM controller is in essence a switch that connects a solar array to a battery. The result is that the voltage of the array will be pulled down to near that of the battery. The Victron PWM charge controller is a good low cost solution for small systems only, when solar cell temperature is moderate to high (between 45°C and 75°C).
Liquid crystal display- For status monitoring and set-up
Load output- Over-discharge of the battery can be prevented by connecting all loads to the load output. The load output will disconnect the load when the battery has been discharged to a pre-set voltage. Some loads (especially inverters) can best be connected directly to the battery, and the inverter remote control connected to the load output. A special interface cable may be needed, please see the manual. The connect and disconnect voltages are adjustable.
Day/night timing of the load output- This option allows for a pre-set ON-time after dusk.
Programmable battery charge algorithm- Pre-programmed algorithms for AGM, GEL, Flooded or LiFePO4 batteries (with internal BMS only)
Two 5 Volt USB outputs- Maximum current (both outputs combined): 2A
Additional information
| Weight | 0.330000 kg |
|---|---|
| Dimensions | 11 × 19 × 5 cm |
Reviews
There are no reviews yet.
Reviews
There are no reviews yet.